SteelBond Pro™ — Patch Cracked Metal in 60 Minutes Without Welding Gear
Patch Cracks, Holes & Stripped Threads — No Welder, No Torch, No Second Try
You tried JB Weld last winter. It came off in a season. SteelBond Pro™ is the 1:1 AB epoxy that grips deep into the metal pores, sets rock solid in 60 minutes, and cures into a steel-reinforced bond you can drill, sand, and paint exactly like the original surface.
Stop Patching the Same Crack Twice
Hardware-store epoxies promise the world and fall apart in three months. Single-tube glues peel right off cast iron. And a welder quote on one cracked housing runs $150+ before you've even paid for parts. SteelBond Pro™ skips all of it — a dual-chamber AB tube that auto-matches every squeeze, no eyeballing two blobs onto a piece of cardboard.
➤ Bonds Cast Iron, Steel, Aluminum & Alloys: Steel-reinforced two-part formula sinks into the surface pores and locks down at the molecular level — grips where superglue and single-tube putties just peel off.
➤ Holds From -40°F to 392°F: Engine bays, exhaust runs, radiators, outdoor pipes, frozen winter joints — the bond doesn't soften in summer heat or crack when the cold snaps in.
➤ Drill It, Sand It, Paint It: Once cured, the patched zone behaves like the metal around it. Tap a fresh thread, refinish the surface, blend the repair until no one can tell it was ever broken.
Meet SteelBond Pro™ — The 1:1 AB Mix That Bonds Like Welded Steel
Push the trigger and the dual-chamber applicator dispenses an exact 1:1 ratio of resin and hardener every time. Smooth it over the crack with the included spatula. Walk away for an hour while the chemical lock pulls the two halves of your metal back together — no torch, no sparks, no 220-volt outlet.
By the 24-hour mark the patched zone is harder than the original metal in most cases — strong enough to drill a fresh bolt hole through, file flush, and prime over.
Why DIY-ers Are Throwing Out Their JB Weld
Mechanics, plumbers, and weekend project guys keep coming back to SteelBond Pro™ for one reason: the patch holds the first time. "I had a hairline crack on my F-150 radiator housing that I'd already JB Weld'ed twice. Did it Saturday with SteelBond. Tuesday morning I drilled a new clip mount straight through the patch — still bone dry." — Mark D.
Walk Back to the Truck Knowing the Fix Will Hold
✓ Patches Hold the First Time: 4,000+ PSI tensile bond once fully cured at 24 hours — drill it, tap it, sand it without flaking or cracking.
✓ Survives Water, Oil, Salt & Solvents: From submerged pipe joints to oil-soaked engine cases — the cured bond shrugs off corrosion, mildew, and chemical exposure.
✓ One 50ml Tube Handles Multiple Repairs: Auto-matching dual chamber means zero waste — squeeze only what you need, cap it, save the rest for the next job.
Patch Any Repair in 3 Steps Flat
Step 1: Scuff the metal with sandpaper and wipe with acetone — clean surface, strong bond.
Step 2: Squeeze a bead onto the included spatula and press it firmly into the crack, hole, or gap.
Step 3: Walk away for 60 minutes. Come back to a rock-solid patch. Full strength locks in at the 24-hour mark — drill, sand, or paint from there.
| SteelBond Pro™ | Welding | Single-Tube Epoxies |
|---|---|---|
| Bonds the first time — no welder, torch, sparks, or 220-volt outlet | ❌ | ❌ |
| Auto-matching 1:1 AB mix — no eyeballing two tubes onto cardboard | ❌ | ❌ |
| Holds -40°F to 392°F, plus water, oil, salt & solvent resistance | ❌ | ❌ |
Specs That Make Pro-Grade Repairs Possible
- Capacity: 50ml dual-chamber tube (3.5 oz total) — handles multiple repairs per tube
- Dimensions: 4.8 x 1.8 inches — fits a tool drawer or glovebox
- Mix Ratio: Auto-matching 1:1 A and B — squeeze the trigger and dispense, no measuring
- Cure Time: 60-minute initial set, 24-hour full cure to drill/sand/paint strength
Still Wondering if It's Right for You?
I've been burned by JB Weld before — what makes this different?
Two things: the auto-matching 1:1 applicator means no bad mixes, and the steel-reinforced formula cures harder than most single-tube epoxies. Surface prep still matters — scuff and wipe with acetone before you apply.
Will it work on cast iron, aluminum, and stainless?
Yes — steel, cast iron, aluminum, brass, copper, and most alloys. Also bonds metal-to-ceramic, metal-to-plastic, and metal-to-stone for cross-material repairs.
Can I drill, tap, and paint over the cured patch?
Yes. After the 24-hour full cure, the patched area handles a drill bit, a tap, sandpaper, and paint exactly like the original metal around it.
Will it hold on a hot engine or exhaust?
The cured bond holds steady from -40°F to 392°F. That covers radiator housings, engine cases, water pumps, and most exhaust components outside of the manifold itself.
Is the patch really waterproof and oil-proof?
Yes — fully submerged pipe joints, oily engine blocks, salt-spray exposure, and mildew-prone basements all hold. The cured bond is non-porous and chemically inert.
Fix It Once, Fix It Right — Backed by Our 60-Day Bond Guarantee
If SteelBond Pro™ doesn't hold your repair through normal use, send it back within 60 days for a full refund — no welder, no second tube, no $200 shop bill. Grab yours below and finish the project today.
Original: $29.99
-70%$29.99
$9.00More Images
SteelBond Pro™ — Patch Cracked Metal in 60 Minutes Without Welding Gear
Patch Cracks, Holes & Stripped Threads — No Welder, No Torch, No Second Try
You tried JB Weld last winter. It came off in a season. SteelBond Pro™ is the 1:1 AB epoxy that grips deep into the metal pores, sets rock solid in 60 minutes, and cures into a steel-reinforced bond you can drill, sand, and paint exactly like the original surface.
Stop Patching the Same Crack Twice
Hardware-store epoxies promise the world and fall apart in three months. Single-tube glues peel right off cast iron. And a welder quote on one cracked housing runs $150+ before you've even paid for parts. SteelBond Pro™ skips all of it — a dual-chamber AB tube that auto-matches every squeeze, no eyeballing two blobs onto a piece of cardboard.
➤ Bonds Cast Iron, Steel, Aluminum & Alloys: Steel-reinforced two-part formula sinks into the surface pores and locks down at the molecular level — grips where superglue and single-tube putties just peel off.
➤ Holds From -40°F to 392°F: Engine bays, exhaust runs, radiators, outdoor pipes, frozen winter joints — the bond doesn't soften in summer heat or crack when the cold snaps in.
➤ Drill It, Sand It, Paint It: Once cured, the patched zone behaves like the metal around it. Tap a fresh thread, refinish the surface, blend the repair until no one can tell it was ever broken.
Meet SteelBond Pro™ — The 1:1 AB Mix That Bonds Like Welded Steel
Push the trigger and the dual-chamber applicator dispenses an exact 1:1 ratio of resin and hardener every time. Smooth it over the crack with the included spatula. Walk away for an hour while the chemical lock pulls the two halves of your metal back together — no torch, no sparks, no 220-volt outlet.
By the 24-hour mark the patched zone is harder than the original metal in most cases — strong enough to drill a fresh bolt hole through, file flush, and prime over.
Why DIY-ers Are Throwing Out Their JB Weld
Mechanics, plumbers, and weekend project guys keep coming back to SteelBond Pro™ for one reason: the patch holds the first time. "I had a hairline crack on my F-150 radiator housing that I'd already JB Weld'ed twice. Did it Saturday with SteelBond. Tuesday morning I drilled a new clip mount straight through the patch — still bone dry." — Mark D.
Walk Back to the Truck Knowing the Fix Will Hold
✓ Patches Hold the First Time: 4,000+ PSI tensile bond once fully cured at 24 hours — drill it, tap it, sand it without flaking or cracking.
✓ Survives Water, Oil, Salt & Solvents: From submerged pipe joints to oil-soaked engine cases — the cured bond shrugs off corrosion, mildew, and chemical exposure.
✓ One 50ml Tube Handles Multiple Repairs: Auto-matching dual chamber means zero waste — squeeze only what you need, cap it, save the rest for the next job.
Patch Any Repair in 3 Steps Flat
Step 1: Scuff the metal with sandpaper and wipe with acetone — clean surface, strong bond.
Step 2: Squeeze a bead onto the included spatula and press it firmly into the crack, hole, or gap.
Step 3: Walk away for 60 minutes. Come back to a rock-solid patch. Full strength locks in at the 24-hour mark — drill, sand, or paint from there.
| SteelBond Pro™ | Welding | Single-Tube Epoxies |
|---|---|---|
| Bonds the first time — no welder, torch, sparks, or 220-volt outlet | ❌ | ❌ |
| Auto-matching 1:1 AB mix — no eyeballing two tubes onto cardboard | ❌ | ❌ |
| Holds -40°F to 392°F, plus water, oil, salt & solvent resistance | ❌ | ❌ |
Specs That Make Pro-Grade Repairs Possible
- Capacity: 50ml dual-chamber tube (3.5 oz total) — handles multiple repairs per tube
- Dimensions: 4.8 x 1.8 inches — fits a tool drawer or glovebox
- Mix Ratio: Auto-matching 1:1 A and B — squeeze the trigger and dispense, no measuring
- Cure Time: 60-minute initial set, 24-hour full cure to drill/sand/paint strength
Still Wondering if It's Right for You?
I've been burned by JB Weld before — what makes this different?
Two things: the auto-matching 1:1 applicator means no bad mixes, and the steel-reinforced formula cures harder than most single-tube epoxies. Surface prep still matters — scuff and wipe with acetone before you apply.
Will it work on cast iron, aluminum, and stainless?
Yes — steel, cast iron, aluminum, brass, copper, and most alloys. Also bonds metal-to-ceramic, metal-to-plastic, and metal-to-stone for cross-material repairs.
Can I drill, tap, and paint over the cured patch?
Yes. After the 24-hour full cure, the patched area handles a drill bit, a tap, sandpaper, and paint exactly like the original metal around it.
Will it hold on a hot engine or exhaust?
The cured bond holds steady from -40°F to 392°F. That covers radiator housings, engine cases, water pumps, and most exhaust components outside of the manifold itself.
Is the patch really waterproof and oil-proof?
Yes — fully submerged pipe joints, oily engine blocks, salt-spray exposure, and mildew-prone basements all hold. The cured bond is non-porous and chemically inert.
Fix It Once, Fix It Right — Backed by Our 60-Day Bond Guarantee
If SteelBond Pro™ doesn't hold your repair through normal use, send it back within 60 days for a full refund — no welder, no second tube, no $200 shop bill. Grab yours below and finish the project today.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
Patch Cracks, Holes & Stripped Threads — No Welder, No Torch, No Second Try
You tried JB Weld last winter. It came off in a season. SteelBond Pro™ is the 1:1 AB epoxy that grips deep into the metal pores, sets rock solid in 60 minutes, and cures into a steel-reinforced bond you can drill, sand, and paint exactly like the original surface.
Stop Patching the Same Crack Twice
Hardware-store epoxies promise the world and fall apart in three months. Single-tube glues peel right off cast iron. And a welder quote on one cracked housing runs $150+ before you've even paid for parts. SteelBond Pro™ skips all of it — a dual-chamber AB tube that auto-matches every squeeze, no eyeballing two blobs onto a piece of cardboard.
➤ Bonds Cast Iron, Steel, Aluminum & Alloys: Steel-reinforced two-part formula sinks into the surface pores and locks down at the molecular level — grips where superglue and single-tube putties just peel off.
➤ Holds From -40°F to 392°F: Engine bays, exhaust runs, radiators, outdoor pipes, frozen winter joints — the bond doesn't soften in summer heat or crack when the cold snaps in.
➤ Drill It, Sand It, Paint It: Once cured, the patched zone behaves like the metal around it. Tap a fresh thread, refinish the surface, blend the repair until no one can tell it was ever broken.
Meet SteelBond Pro™ — The 1:1 AB Mix That Bonds Like Welded Steel
Push the trigger and the dual-chamber applicator dispenses an exact 1:1 ratio of resin and hardener every time. Smooth it over the crack with the included spatula. Walk away for an hour while the chemical lock pulls the two halves of your metal back together — no torch, no sparks, no 220-volt outlet.
By the 24-hour mark the patched zone is harder than the original metal in most cases — strong enough to drill a fresh bolt hole through, file flush, and prime over.
Why DIY-ers Are Throwing Out Their JB Weld
Mechanics, plumbers, and weekend project guys keep coming back to SteelBond Pro™ for one reason: the patch holds the first time. "I had a hairline crack on my F-150 radiator housing that I'd already JB Weld'ed twice. Did it Saturday with SteelBond. Tuesday morning I drilled a new clip mount straight through the patch — still bone dry." — Mark D.
Walk Back to the Truck Knowing the Fix Will Hold
✓ Patches Hold the First Time: 4,000+ PSI tensile bond once fully cured at 24 hours — drill it, tap it, sand it without flaking or cracking.
✓ Survives Water, Oil, Salt & Solvents: From submerged pipe joints to oil-soaked engine cases — the cured bond shrugs off corrosion, mildew, and chemical exposure.
✓ One 50ml Tube Handles Multiple Repairs: Auto-matching dual chamber means zero waste — squeeze only what you need, cap it, save the rest for the next job.
Patch Any Repair in 3 Steps Flat
Step 1: Scuff the metal with sandpaper and wipe with acetone — clean surface, strong bond.
Step 2: Squeeze a bead onto the included spatula and press it firmly into the crack, hole, or gap.
Step 3: Walk away for 60 minutes. Come back to a rock-solid patch. Full strength locks in at the 24-hour mark — drill, sand, or paint from there.
| SteelBond Pro™ | Welding | Single-Tube Epoxies |
|---|---|---|
| Bonds the first time — no welder, torch, sparks, or 220-volt outlet | ❌ | ❌ |
| Auto-matching 1:1 AB mix — no eyeballing two tubes onto cardboard | ❌ | ❌ |
| Holds -40°F to 392°F, plus water, oil, salt & solvent resistance | ❌ | ❌ |
Specs That Make Pro-Grade Repairs Possible
- Capacity: 50ml dual-chamber tube (3.5 oz total) — handles multiple repairs per tube
- Dimensions: 4.8 x 1.8 inches — fits a tool drawer or glovebox
- Mix Ratio: Auto-matching 1:1 A and B — squeeze the trigger and dispense, no measuring
- Cure Time: 60-minute initial set, 24-hour full cure to drill/sand/paint strength
Still Wondering if It's Right for You?
I've been burned by JB Weld before — what makes this different?
Two things: the auto-matching 1:1 applicator means no bad mixes, and the steel-reinforced formula cures harder than most single-tube epoxies. Surface prep still matters — scuff and wipe with acetone before you apply.
Will it work on cast iron, aluminum, and stainless?
Yes — steel, cast iron, aluminum, brass, copper, and most alloys. Also bonds metal-to-ceramic, metal-to-plastic, and metal-to-stone for cross-material repairs.
Can I drill, tap, and paint over the cured patch?
Yes. After the 24-hour full cure, the patched area handles a drill bit, a tap, sandpaper, and paint exactly like the original metal around it.
Will it hold on a hot engine or exhaust?
The cured bond holds steady from -40°F to 392°F. That covers radiator housings, engine cases, water pumps, and most exhaust components outside of the manifold itself.
Is the patch really waterproof and oil-proof?
Yes — fully submerged pipe joints, oily engine blocks, salt-spray exposure, and mildew-prone basements all hold. The cured bond is non-porous and chemically inert.
Fix It Once, Fix It Right — Backed by Our 60-Day Bond Guarantee
If SteelBond Pro™ doesn't hold your repair through normal use, send it back within 60 days for a full refund — no welder, no second tube, no $200 shop bill. Grab yours below and finish the project today.
