VisiTrace™ — Spot Studs, Wires & Pipes Before You Drill a Single Hole
Spot Studs, Wires & Pipes Before You Drill a Single Hole
You're standing in front of the wall with a drill in your hand and no idea what's behind it. VisiTrace™ is the 4-in-1 wall scanner that shows you what's hiding — metal, copper wire, wood studs, live electrical, copper pipe — so you mark the safe spot and drill once, not three times.
Stop Drilling Blind and Hoping You Don't Hit a Wire
One blind hole into a live cable and your Saturday turns into a $300 call to an electrician. One into a copper pipe and you're cutting drywall. Cheap stud-only finders beep at everything, miss what they can't read, and leave you guessing where the center actually is.
➤ 4 Modes, One Sweep: Switch between metal, wood stud, live wire, and copper pipe detection — one device replaces three you'd otherwise keep losing in the toolbox.
➤ Pinpoints Dead Center: Edge and center indicators with a 0.1cm depth reading on the LCD — you mark the exact middle of the stud, not "somewhere around here."
➤ Built for First-Timers: Three buttons, audible beep, signal bar that fills as you get closer — figure it out in 30 seconds, no instruction manual needed.
How VisiTrace™ Sees What's Behind Drywall, Brick & Tile
Inside the scanner is a wideband sensor that reads three different signal types — magnetic field (ferrous metal like rebar and nails), capacitance shift (wood studs and non-ferrous metal like copper), and AC field (live electrical). Press the mode button for what you're hunting, slide across the wall, and the LCD bar fills as you cross the target. Hit center and the screen reads "Edge → Center → Edge" with depth in centimeters.
No more guessing whether that beep was a stud or a screw. No more drilling, missing, and patching.
Why DIYers and Trades Both Keep One on Their Belt
Hanging a heavy mirror. Mounting a TV. Running cable through a remodel. Drilling a vent line. The people using VisiTrace™ aren't picky — they just want to know what's behind the wall before the drill bit goes in.
"I'm not handy. I bought this to hang a 65-inch TV by myself instead of paying $150 for an installer. Found both studs in under a minute, drilled twice, done. Wish I'd had it for the last house too." — Marcus T.
Know Exactly What's Behind Every Wall Before You Touch the Drill
✓ Save Your Drywall (and Your Wallet): Skip the $300 electrician call and the second trip for spackle — find the safe spot the first time.
✓ One Device, Every Wall Type: Works through drywall, plaster, brick, concrete, and tile — no swapping tools mid-project.
✓ Confidence Before Every Drill: See edge, center, and depth on the LCD — mark it, drill it, move on.
Three Steps to a Hole You Won't Regret
Step 1: Press the mode button — metal, stud, wire, or pipe — based on what you're trying to find (or avoid).
Step 2: Hold VisiTrace™ flat against the wall and slide it slowly sideways. Watch the signal bar fill and listen for the beep.
Step 3: When the LCD reads "Center" with 100% signal, mark the wall with a pencil. That's your safe spot.
| VisiTrace™ 4-in-1 Scanner | Cheap Stud-Only Finders | Knock-and-Hope |
|---|---|---|
| Finds metal, wood, wire, and pipe in one sweep | ❌ Studs only — misses wires | ❌ Pure guesswork |
| Reads edge, center, and depth on LCD | ❌ One LED that beeps everywhere | ❌ |
| AC live-wire warning before you drill | ❌ | ❌ |
Specs at a Glance
- Dimensions: 7.1in x 2.6in x 1.4in — fits a back pocket or tool pouch
- Power: Single 9V battery (sold separately) — swap in 10 seconds
- Detection Modes: Ferrous metal, non-ferrous metal (copper), wood stud, AC live wire
- Display: Backlit LCD with edge/center indicator, signal bar, and depth in cm/inches
- Colors: Red, Yellow, or Silver
Real Questions People Ask Before They Buy
Will it work on plaster, brick, or concrete walls — or just drywall?
Works on drywall, plaster, brick, tile, and concrete. Depth range drops as the wall gets denser — drywall reads deepest, concrete shallowest — but all four modes work on all of them.
I've never used a stud finder. Will I actually figure this out?
Three buttons, one LCD, one beeper. Pick your mode, slide it on the wall, mark the spot where the bar hits 100% and the screen says Center. People who've never owned a tool find their first stud in about a minute.
How deep does it actually scan?
Up to roughly 2 inches for wood studs, deeper for metal and live AC current. Plenty for standard interior walls. The LCD shows you the depth as you scan so you're never guessing.
Does it actually warn me about live wires before I drill?
Yes — put it in AC mode and it lights up and beeps when it crosses a live cable. That's the mode you want before any TV mount, shelf, or new outlet.
What if it shows up and doesn't read accurately for me?
Send it back. If VisiTrace™ doesn't read your walls cleanly within 30 days, we refund every cent — no return-shipping song and dance.
Drill Once. Get It Right. Move On With Your Day.
The next hole you drill is either going to land on the stud or land on a wire. VisiTrace™ tells you which before you pull the trigger — and if it ever doesn't, we refund you in full within 30 days. Grab one in your color, drop in a 9V, and stop guessing what's behind your walls.
Original: $34.99
-70%$34.99
$10.50More Images
VisiTrace™ — Spot Studs, Wires & Pipes Before You Drill a Single Hole
Spot Studs, Wires & Pipes Before You Drill a Single Hole
You're standing in front of the wall with a drill in your hand and no idea what's behind it. VisiTrace™ is the 4-in-1 wall scanner that shows you what's hiding — metal, copper wire, wood studs, live electrical, copper pipe — so you mark the safe spot and drill once, not three times.
Stop Drilling Blind and Hoping You Don't Hit a Wire
One blind hole into a live cable and your Saturday turns into a $300 call to an electrician. One into a copper pipe and you're cutting drywall. Cheap stud-only finders beep at everything, miss what they can't read, and leave you guessing where the center actually is.
➤ 4 Modes, One Sweep: Switch between metal, wood stud, live wire, and copper pipe detection — one device replaces three you'd otherwise keep losing in the toolbox.
➤ Pinpoints Dead Center: Edge and center indicators with a 0.1cm depth reading on the LCD — you mark the exact middle of the stud, not "somewhere around here."
➤ Built for First-Timers: Three buttons, audible beep, signal bar that fills as you get closer — figure it out in 30 seconds, no instruction manual needed.
How VisiTrace™ Sees What's Behind Drywall, Brick & Tile
Inside the scanner is a wideband sensor that reads three different signal types — magnetic field (ferrous metal like rebar and nails), capacitance shift (wood studs and non-ferrous metal like copper), and AC field (live electrical). Press the mode button for what you're hunting, slide across the wall, and the LCD bar fills as you cross the target. Hit center and the screen reads "Edge → Center → Edge" with depth in centimeters.
No more guessing whether that beep was a stud or a screw. No more drilling, missing, and patching.
Why DIYers and Trades Both Keep One on Their Belt
Hanging a heavy mirror. Mounting a TV. Running cable through a remodel. Drilling a vent line. The people using VisiTrace™ aren't picky — they just want to know what's behind the wall before the drill bit goes in.
"I'm not handy. I bought this to hang a 65-inch TV by myself instead of paying $150 for an installer. Found both studs in under a minute, drilled twice, done. Wish I'd had it for the last house too." — Marcus T.
Know Exactly What's Behind Every Wall Before You Touch the Drill
✓ Save Your Drywall (and Your Wallet): Skip the $300 electrician call and the second trip for spackle — find the safe spot the first time.
✓ One Device, Every Wall Type: Works through drywall, plaster, brick, concrete, and tile — no swapping tools mid-project.
✓ Confidence Before Every Drill: See edge, center, and depth on the LCD — mark it, drill it, move on.
Three Steps to a Hole You Won't Regret
Step 1: Press the mode button — metal, stud, wire, or pipe — based on what you're trying to find (or avoid).
Step 2: Hold VisiTrace™ flat against the wall and slide it slowly sideways. Watch the signal bar fill and listen for the beep.
Step 3: When the LCD reads "Center" with 100% signal, mark the wall with a pencil. That's your safe spot.
| VisiTrace™ 4-in-1 Scanner | Cheap Stud-Only Finders | Knock-and-Hope |
|---|---|---|
| Finds metal, wood, wire, and pipe in one sweep | ❌ Studs only — misses wires | ❌ Pure guesswork |
| Reads edge, center, and depth on LCD | ❌ One LED that beeps everywhere | ❌ |
| AC live-wire warning before you drill | ❌ | ❌ |
Specs at a Glance
- Dimensions: 7.1in x 2.6in x 1.4in — fits a back pocket or tool pouch
- Power: Single 9V battery (sold separately) — swap in 10 seconds
- Detection Modes: Ferrous metal, non-ferrous metal (copper), wood stud, AC live wire
- Display: Backlit LCD with edge/center indicator, signal bar, and depth in cm/inches
- Colors: Red, Yellow, or Silver
Real Questions People Ask Before They Buy
Will it work on plaster, brick, or concrete walls — or just drywall?
Works on drywall, plaster, brick, tile, and concrete. Depth range drops as the wall gets denser — drywall reads deepest, concrete shallowest — but all four modes work on all of them.
I've never used a stud finder. Will I actually figure this out?
Three buttons, one LCD, one beeper. Pick your mode, slide it on the wall, mark the spot where the bar hits 100% and the screen says Center. People who've never owned a tool find their first stud in about a minute.
How deep does it actually scan?
Up to roughly 2 inches for wood studs, deeper for metal and live AC current. Plenty for standard interior walls. The LCD shows you the depth as you scan so you're never guessing.
Does it actually warn me about live wires before I drill?
Yes — put it in AC mode and it lights up and beeps when it crosses a live cable. That's the mode you want before any TV mount, shelf, or new outlet.
What if it shows up and doesn't read accurately for me?
Send it back. If VisiTrace™ doesn't read your walls cleanly within 30 days, we refund every cent — no return-shipping song and dance.
Drill Once. Get It Right. Move On With Your Day.
The next hole you drill is either going to land on the stud or land on a wire. VisiTrace™ tells you which before you pull the trigger — and if it ever doesn't, we refund you in full within 30 days. Grab one in your color, drop in a 9V, and stop guessing what's behind your walls.
Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
Spot Studs, Wires & Pipes Before You Drill a Single Hole
You're standing in front of the wall with a drill in your hand and no idea what's behind it. VisiTrace™ is the 4-in-1 wall scanner that shows you what's hiding — metal, copper wire, wood studs, live electrical, copper pipe — so you mark the safe spot and drill once, not three times.
Stop Drilling Blind and Hoping You Don't Hit a Wire
One blind hole into a live cable and your Saturday turns into a $300 call to an electrician. One into a copper pipe and you're cutting drywall. Cheap stud-only finders beep at everything, miss what they can't read, and leave you guessing where the center actually is.
➤ 4 Modes, One Sweep: Switch between metal, wood stud, live wire, and copper pipe detection — one device replaces three you'd otherwise keep losing in the toolbox.
➤ Pinpoints Dead Center: Edge and center indicators with a 0.1cm depth reading on the LCD — you mark the exact middle of the stud, not "somewhere around here."
➤ Built for First-Timers: Three buttons, audible beep, signal bar that fills as you get closer — figure it out in 30 seconds, no instruction manual needed.
How VisiTrace™ Sees What's Behind Drywall, Brick & Tile
Inside the scanner is a wideband sensor that reads three different signal types — magnetic field (ferrous metal like rebar and nails), capacitance shift (wood studs and non-ferrous metal like copper), and AC field (live electrical). Press the mode button for what you're hunting, slide across the wall, and the LCD bar fills as you cross the target. Hit center and the screen reads "Edge → Center → Edge" with depth in centimeters.
No more guessing whether that beep was a stud or a screw. No more drilling, missing, and patching.
Why DIYers and Trades Both Keep One on Their Belt
Hanging a heavy mirror. Mounting a TV. Running cable through a remodel. Drilling a vent line. The people using VisiTrace™ aren't picky — they just want to know what's behind the wall before the drill bit goes in.
"I'm not handy. I bought this to hang a 65-inch TV by myself instead of paying $150 for an installer. Found both studs in under a minute, drilled twice, done. Wish I'd had it for the last house too." — Marcus T.
Know Exactly What's Behind Every Wall Before You Touch the Drill
✓ Save Your Drywall (and Your Wallet): Skip the $300 electrician call and the second trip for spackle — find the safe spot the first time.
✓ One Device, Every Wall Type: Works through drywall, plaster, brick, concrete, and tile — no swapping tools mid-project.
✓ Confidence Before Every Drill: See edge, center, and depth on the LCD — mark it, drill it, move on.
Three Steps to a Hole You Won't Regret
Step 1: Press the mode button — metal, stud, wire, or pipe — based on what you're trying to find (or avoid).
Step 2: Hold VisiTrace™ flat against the wall and slide it slowly sideways. Watch the signal bar fill and listen for the beep.
Step 3: When the LCD reads "Center" with 100% signal, mark the wall with a pencil. That's your safe spot.
| VisiTrace™ 4-in-1 Scanner | Cheap Stud-Only Finders | Knock-and-Hope |
|---|---|---|
| Finds metal, wood, wire, and pipe in one sweep | ❌ Studs only — misses wires | ❌ Pure guesswork |
| Reads edge, center, and depth on LCD | ❌ One LED that beeps everywhere | ❌ |
| AC live-wire warning before you drill | ❌ | ❌ |
Specs at a Glance
- Dimensions: 7.1in x 2.6in x 1.4in — fits a back pocket or tool pouch
- Power: Single 9V battery (sold separately) — swap in 10 seconds
- Detection Modes: Ferrous metal, non-ferrous metal (copper), wood stud, AC live wire
- Display: Backlit LCD with edge/center indicator, signal bar, and depth in cm/inches
- Colors: Red, Yellow, or Silver
Real Questions People Ask Before They Buy
Will it work on plaster, brick, or concrete walls — or just drywall?
Works on drywall, plaster, brick, tile, and concrete. Depth range drops as the wall gets denser — drywall reads deepest, concrete shallowest — but all four modes work on all of them.
I've never used a stud finder. Will I actually figure this out?
Three buttons, one LCD, one beeper. Pick your mode, slide it on the wall, mark the spot where the bar hits 100% and the screen says Center. People who've never owned a tool find their first stud in about a minute.
How deep does it actually scan?
Up to roughly 2 inches for wood studs, deeper for metal and live AC current. Plenty for standard interior walls. The LCD shows you the depth as you scan so you're never guessing.
Does it actually warn me about live wires before I drill?
Yes — put it in AC mode and it lights up and beeps when it crosses a live cable. That's the mode you want before any TV mount, shelf, or new outlet.
What if it shows up and doesn't read accurately for me?
Send it back. If VisiTrace™ doesn't read your walls cleanly within 30 days, we refund every cent — no return-shipping song and dance.
Drill Once. Get It Right. Move On With Your Day.
The next hole you drill is either going to land on the stud or land on a wire. VisiTrace™ tells you which before you pull the trigger — and if it ever doesn't, we refund you in full within 30 days. Grab one in your color, drop in a 9V, and stop guessing what's behind your walls.
